Ingen varer
Priserne er inklusiv moms
LED SnakeSpot på 2W med fleksibel lampearm Mål: Ø: 25 x 80 mm 60 graders vinkel Effekt: 2 watt Farve: varm hvid (2.700 kelvin) Vinkel: 60° Lumens: 110
This hanger clamps to any mic stand to put your headphones in easy reach. It features two convenient slots to keep your headphone cables neat and tidy, and the plastic set screw tip protects the stand's finish.
The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped. In addition to locking XLR...
LD Sytems HPA 4 - a compact and powerful headphone amplifier The LDHPA4 has small dimensions, can handle up to 4 headphones and has an output power with no equal in its class. That means high volume with no distortion. With these features the LDHPA4 is an essential tool for every project- and home studio.
LDHPA6 6-Channel Rackmount Headphone Amplifier The LD Systems HPA 6 is a highly flexible 1U 19 rack format headphone amplifier with 6 fully independent channels and comprehensive features for a wide range of professional audio monitoring applications. Each channel provides a 6.3 mm TRS headphone output on the front panel with level control, mono/stereo...
The LDIEHP1 is an extremely light, professional in-ear monitor with a broad frequency response range and a clean, balanced sound. It is very well shielded against extraneous noise and comes with three different sets of tips to fit practically any pair of ears perfectly. Additional convenience is ensured by a generously long, 1.5m-long cable. A gold-plated...
The LD Systems PPA 2 is a very compact analogue phono preamplifier, which equalises the extremely low output signal of conventional turntables to RIAA standards. It allows you to connect to devices without any phono input, such as mixers, PA power amplifiers or sound cards. The phono inputs are designed as RCA jacks, just like the line outputs; the PPA 2...
Passive DI box especially designed for guitars. The PDI09 can be connected between an effect device or amplifier and the mixing console. The PDI09 is not suitable for direct connection to a guitar. Integrated filter circuits simulate the authentic "speaker" sound. Tone can be varied between "Mellow", "Normal", or "Bright".
The Palmer Speaker Simulator PDi 03 - available in 2, 4, 8 and 16 Ohm The PDI03 Palmer speaker simulator combines load impedance, a signal splitter and DI box especially designed for guitars. All functions are optimised for live and recording applications. Instead of being connected to a loudspeaker, the PDI03 is connected directly to the amplifier...
Special DI box with loadbox for guitars. The integrated load resistor permits tube amplifiers up to approximately 120 W to be connected to the PGA04, bypassing a loudspeaker. A jack socket (unbalanced) and balanced XLR connector are available for direct pickup of the signal. The extensive filter section provides for a realistic simulation of classic...
Special DI box with loadbox for guitars. The integrated load resistor permits tube amplifiers up to approximately 120 W to be connected to the PGA04, bypassing a loudspeaker. A jack socket (unbalanced) and balanced XLR connector are available for direct pickup of the signal. The extensive filter section provides for a realistic simulation of classic...
The ah PAD series is designed to isolate studio monitors acoustically, i.e., avoid disturbing resonances with the surface on which they stand, which results in a significantly improved sound. The two-component design results in three possible combinations (horizontal placement + two different angles.
The ah PAD series is designed to isolate studio monitors acoustically, i.e., avoid disturbing resonances with the surface on which they stand, which results in a significantly improved sound. The two-component design results in three possible combinations (horizontal placement + two different angles.
This hanger clamps to any desk with 5 to 45 mm thickness to put your headphones in easy reach. It features two convenient slots to keep your headphone cables neat and tidy, and the plastic set screw tip protects your desk's finish.
This wall-mount hanger lets you put your headphones in easy reach. It features two convenient slots to keep your headphone cables neat and tidy.
This durable, lightweight carry case is designed for storing and transporting your in-ear headphones. The rigid outer shell with soft fleece lining provides solid protection from impact, scratches and dust. The case features an internal mesh pocket for ear tips and other accessories, a sturdy zip closure and detachable carabiner belt clip.